The last of a dying bred. They may not always be the cheapest but the knowledgeable staff is…read morealways helpful.

I have a had one good experience here but the last 3 times I attempted to get machine work done…read morehere the employees where surly and completely uninterested in my job. A lot of people wonder why there are so few of these type of businesses left. It's because they tend to have terrible customer service. This one is no exception .

From nowhere, unannounced, I arrived at Tri-C Machine's doorstep as my Arcimoto FUV fender brackets…read morehad failed and needed expert services. Tri-C Machine did not turn me away, but rather was interested to know more. Jim and Steve of Tri-C provided a bespoke solution by fabricating a custom fix for my broken fender bracket. My Arcimoto FUV is back on the road and has never performed better. -- Thank you Jim & Steve

I guarantee you don't get what you pay for I had to Rams built actually three the first one is fine…read morethey put a harden shaft in as I requested. The next two they built for me we're supposed to be the same hard and shaft in the same type ram and neither of them were hardened they That bent with very little use he said they would not bend but we're so hard they would have to break. Well they bent in about hour of light use. I feel ripped off. Possibility of going to court. was very litt Den Almost $2000 for junk im worried that if I use the one that I just picked up its going to be the same junk. I ordered a new one online from magister hydraulic supposed to be 14k capable only running 3k for 1/4 the price k

Richard Boutry is a great man, with a great reputation for building bad ass engines (that's good!).read more

Sent the head of my engine to get resurfaced. The price was beyond decent and was even able to…read moreafford to get my head pressure checked and cleaned.

I had a 4.0L Jeep block and head done over the summer. Rich was super helpful making suggestions as…read moreto necessary work without pushing the unnecessary. The head work was solid with all new valves and passed a leak down test before installation. The block machine work was superb as the hone was done to tolerance on the piston and ring kit I purchased. Rich tanked and blasted the block for a slight extra charge but worth the money. The jeep is back on the ground and the first 500 miles are in w/o any issues. Lots more power than before the rebuild.

Be very, very careful getting advice here. On two occasions, staff has steered me wrong on parts…read moreand other auto consumables. Counter staff appear aloof and too busy to help the average consumer. Strongly encourage EM-management take a look at their business model if they want to survive in a competitive market, or, become more profitable, in general.

Been going to what used to be Riebe's for 22 years. Went last week and the young man had an off…read moreday. Anyway, he had me place my bank card in the holder. It did its usual beeping and do not remove card. Then the machine clicked "Approved" so I took my card out. The salesperson then told me the transaction did not go through and I need to go to the cashier in the front of the store. I later checked my bank account and found (not to my surprise) two transactions of $50.76. I called and spoke with the manager who told me I had to bring my receipt in. I did the next day and the 40 year veteran salesperson told me the store is not responsible for the double charge and to take it up with the bank. It cost me $7.00 round trip to be denied crediting my account. The manager could've reversed the overcharge but chose not to. Where's Bart when you need him? Anyway, I came home and filed with my bank on the double charge. I am now tempted to shop at O'Reillys Auto Parts and/or Autozone. Great way to treat a long-time loyal customer - bye bye Napa...

I'm very pleased with how helpful LJ's speed shop has been to me! I showed up on a random day…read moreneeding a bearing pressed into a hub and they were nothing but honest and knowledgeable. They found the parts I needed and even recommended I replace the spindle entirely which will keep me safer on the road. All for a good price! Definitely going back to LJ's when I need some help! Easy 5 star rating from me.

Old style speed shop great customer service if they don't have your part on hand they'll order it…read moreand put a rush on it

I was told the owner Bob Ottow has been manufacturing custom parts in his machine shop for years…read more He has almost every conceivable machine to manufacture parts in his facility. I went to Bob to have a fuel pump custom machined and found it to be done to exacting tolerances and with impeccable fit and finish. Also he showed an over abundance of knowledge and expertise in the machine and aerospace industry industries. I found everything there from NHRA Top Fuel fuel and clutch system parts manufactured by him, to lawnmower rebuilds. The spectrum of work was incredible. Price was also reasonable and done in a timely fashion.