Cancel

    Open app

    Search

    Golteez

    3.0 (2 reviews)
    Closed 9:00 am - 5:00 pm

    Golteez Photos

    You might also consider

    Recommended Reviews - Golteez

    Your trust is our priority, so businesses can't pay to alter or remove their reviews. Learn more about reviews.
    Yelp app icon
    Browse more easily on the app
    Review Feed Illustration

    2 years ago

    Helpful 0
    Thanks 0
    Love this 0
    Oh no 0

    10 years ago

    Helpful 0
    Thanks 0
    Love this 0
    Oh no 0

    You might also consider

    Verify this business for free

    People searched for Toy Stores 1,188 times last month within 15 miles of this business.

    Verify this business

    Mini Moto Toys - Falling apart

    Mini Moto Toys

    1.5(8 reviews)
    4.0 kmSaint-Laurent

    https://minimototoys.com/products/jp-101-yellow…read more I purchased this car and there are a significant number of problems with it. Here is just part of the problem because I stopped keeping track after it became obvious this was more than just a genuine mistake or manufacturing defect. - Cable for Horn Wire for horn just harnessed to radio PCB with absolutely no tie wraps or anything to prevent force being put on the connector on the board. Well putting on the steering wheel, The harness slid right off of the PCB and getting inside was a huge pain in the ass. A simple tie wrap is the proper solution. Cheap and lazy. Disassembling the dashboard to get inside was a huge pain in the ass. After finally getting in there, I found out that the problem was more than just no tie-wrap preventing it from being pulled off the PCB. The harnesses do not match and do not fit together! It is completely loose. Clearly the wiring for the steering wheel and the radio module were purchased from totally different vendors and didn't fit together and you guys didn't bother to even replace the hardness to a correct one that fits. You can see below that even pushing the hardness all the way down, it doesn't stay in place because it isn't made for it. The only way to prevent it from sliding out was to hot glue it. -Steering column Steering column rod was too short to install the steering wheel so I couldn't put the pin in. It's because the rod has ~2" of play in it which allows the rod to slide down towards the floor. This causes it to fall out of the grooves for the steering wheel drive motor so even if you try to push the rod back up, it won't move. For a while I thought it was the wrong steering wheel or the rod was too short until I turned the car upside down and realized the problem was it had slipped out of the motor assembly. Getting it put together was a huge pain in the ass because I had to hold the rod up and in place in the motor while trying to attach the steering wheel and insert the pin. This is a very sloppy design. What's worse, the instruction manual said nothing about this so I had to waste so much time figuring it out on my own. - TERRIBLE Instructions The worst instructions I've ever seen. An incredibly poor translation that mostly doesn't even make sense. Obvious mistakes where whole sentences are repeated and slightly different ways as if the person editing the original document didn't bother to take out any revisions The diagrams are so small with so much going on that it is absolutely useless. You cannot see what you are supposed to be doing Even if it was written in proper English, made sense, and had functional diagrams, the instruction book didn't match the car. Yes it was the same model and the picture was on the cover but the instructions talk about mounting things that arent part of the car while other components that I do have are never mentioned anywhere. There are three different types of screws provided but they referred all of them as M4*12. These are not all M4*12. So either the instructions are so bad that they didn't bother to clarify which of the three different types of screws to use for particular parts or I just got a handful of whatever screws they had laying on the floor. -TERRIBLE build quality In addition to what I described above, the work you guys did to install the wiring and motors was absolutely terrible. One of the back motors was not mounted at all since the strap holding it was completely deformed and the motor slipped out. The other rear motor was loose and almost falling out. A few of the components and wiring bundles were tie wrapped but the majority of it was left dangling and exposed (including what I mentioned above about the horn wiring harness). Here is one example of the inline auto-reset fuse on the front right motor. It was not tie wrapped down or mounted to anything so it was handing down almost touching the floor. This would have certainly snagged onto something and ripped apart, possibly causing a fire or injury if it happened before the fuse. The front left was tie wrapped and mounted but not front right so obviously you knew it should have been done but didn't bother doing both sides. I can't believe how much time I wasted on this and how poorly this was made.

    The ride on toys they sell are junk and way over priced. Their website advertising leads you to…read morebelieve the motors are strong and powerful but my 4 year old 40 lb son is too much for the toy. it goes very slow on any incline even slight. the toy was also shipped via regular FedEx instead of freight. it arrived with a damaged hood. their customer service is slow and and does not provide adequate communication. it took more than 2 1/2 weeks to get a replacement hood and it does not have the Range Rover lettering and so clearly not the original. $549 for a cheap, low power China made crappy toy with poor customer service. don't buy from this online merchant, it's a ripoff.

    Photos
    Mini Moto Toys - Power cables to motor weren't not mounted to anything. Almost touching the floor and very dangerous

    Power cables to motor weren't not mounted to anything. Almost touching the floor and very dangerous

    Mini Moto Toys - Wiring harnesses weren't even matching so they wouldn't go in properly.

    Wiring harnesses weren't even matching so they wouldn't go in properly.

    Mini Moto Toys - Wiring harnesses weren't even matching so they wouldn't go in properly.

    See all

    Wiring harnesses weren't even matching so they wouldn't go in properly.

    Golteez - toys - Updated May 2026

    Loading...
    Loading...
    Loading...