This is a long overdue review, but the guys at Aero Welding helped me save my sofa from Living…read moreSpaces. I purchased a Bonaterra pullout sofa and there is a very slim rod that goes under the pull out bed. Well, that rod ended up snapping in half and every time I sat on the sofa, it ended up sinking. I called Living Spaces and they were of no help since I was out of my warranty. I called furniture repair places and they said I'd have to purchase the entire pull out mechanism, which made no sense given that I just needed to replace the one rod. Lo and behold, I contacted the guys at Aero Welding, and they were like no problem, we can manufacture the rod. They just needed the measurements (it would have been better if I had brought the original rod, but I had thrown it away by the time I got to them) and not only were able to recreate the rod, but they made it more sturdy. The turnaround period was very reasonable as well. Once I got home, I placed the rod and it fit perfect. But the moment of truth was to sit on it and see if it held. And it did! The sofa no longer sank and it felt firm and sturdy! Felt brand new again! Shout out to the guys at Aero Welding for all of their help! Give them a call for any welding needs!

Excellent service, pricing, speed of turnaround and quality of work. Just a great experience. I…read morecalled, confirmed they would be in, brought it to their location and they gave me a fair price and got it done while I waited. I brought it in missing some nuts to hold the electronics in place and he went ahead and put in the screws and even painted the area they welded- which was not really necessary. Attention to detail and really friendly. Thanks!! It is worth driving a little farther for this service.

Good prices. Friendly service. Definitely go here vs any big box fit metal. I'm an amateur / hobby…read moremetal worker, for reference.

If you're looking for industrial metals M & K Metals is the best local place. They sell big metal…read morein big quantity, bigger than I can use for my projects. so MY favorite part of the biz is the "REM"s section. (REM = Remainders) That's where they sell the left over cut scraps of all kinds of metal. I can usually find something that will work for my current project there. I'm usually looking for angle or square tube. Today I found a piece of flat aluminum - perfect for my project. About 5 pounds. $14 out the door. :-) FYI: REMs sell by the pound, at something like half price versus the full size pieces. When you buy rems, you weight it on the scale by the front door across from the cashiers. I'll upload a photo of their current price sheet for REMs. The REM prices are posted in the REM area, which is straight through the retail store & then turn left. Customers are allowed in the REM area. M&K is also improving the wares in their store. They are selling more helpful pre-built metal parts than they used to. Gate hinges, bolts, nuts, lock boxes for steel screen doors, weld on tabs, casters, tools, drill bits, grinding wheels, gloves, & more.

Needed a O2 Sensor bung welded on my exhaust pipe. I brought the pipe down to M&S and they took…read morecare of me right away, welded up perfectly and I was out the door at a fair price.

Just got back from buying some steel from M&S and thought I'd leave a yelp review. I 've been doing…read morebusiness with M&S for years now. They always have the steel materials i need and their prices are very competitive to other places. When i place my steel orders the employees there always get my order fast and right. The ladies in the office are very friendly and helpful. If you need steel materials for your projects this is the place to go.

Service was on time and professional. Exactly what I wanted and for a great price!…read more I needed a metal fence piece welded back that had been pried open by a would-be intruder. And most importantly a more reliable lock for my rear gate that couldn't be so easily encouraged open.

I hire Pedro Marquez and first of all he completed the job about a month later then he promised and…read morewhen he finally finished i noticed that he used a cheaper and thinner metal then that he promised, and the worst part is the painting job, is paint everywhere including the new concrete steps.

I took an electrical panel door to CMF for powder-coating. The finished product was "just OK"…read more I dropped the project off on a Monday and was told it would take one week to complete. I called the following Tuesday and left a message for Antwione. I called again on Wednesday and left a message for Antwione. I called again on Thursday and finally got a hold of Antwione. He seemed confused by who I was but after I reminded him, he confirmed that the piece was ready for pick-up. When I picked up the piece Antwione showed me what I needed to do to reattach the door (use a screwdriver to pry the butterfly clips apart) but would not do it for me (I suppose he didn't want the liability if anything broke). He also explained that the spring latch would bounce back once the door was attached. Unfortunately, the spring latch broke the minute we got the butterfly clips back on. The door (which was warped during the process and will no longer lie flat) is now being held shut with velcro strips. He charged me $130 for the project which I later found out should have probably been in the $85 - $100 range. You can see the "hook marks" where the door was held in place during the powder-coating process but since they are on the inside of the door, I'm not going to complain too loudly. I won't bring another piece back here - there is no justification for it based on the quality, price or service received.

I needed a job done for an important client I was recommended to come here and I wasn't sure being…read morethat my customers are important but I'm so glad I took a chance with them. The staff is super friendly everyone was really helpful I walked in and was helped right away as if they knew me. They knew what they were talking about answered all my questions I needed this work done by Friday and I was called Thursday morning letting me know my parts were ready they deliver but no need for my small order!!! Going to use them more often for all my anodize and powder coating, tumbling and laser engraving needs really is a one stop shop thanks again CMF

Electropolishing, Passivation, Thermo Deburr, Sand Blasting, Tumble deburr, Vibra debarread more

From the owner: Deburr, Electropolish, Passivation, Thermal Deburr, Abrasive Blasting, Vibra Deburr, Degreasingread more

Contacted Dennis via yelp on Friday and he came out that day for our service request. Gave us an…read moreestimate, which I was happy with. Dennis explained to us what he could do to make the gate safe, functional and look good. He did better than what we even expected. He even installed a new lock for us. Our gate was rusted out and wasn't lining up, the track was twisted and lock was not working right. Very professional and fast! Great value! Great Work! We will definitely call hI'm for future projects

Dennis fabricated and installed two railings for us. He had good ideas for the design which we…read morereally liked. Pictures are on his website. His pricing was fair so we went with him. The installation was a little tricky but Dennis figured it out with no problem. He had the fabricated rails ready to install sooner than expected and was able to do the installation in a day. Dennis and his helper were extremely professional , did the work quickly and cleaned up completely. Very happy with our decision to hire him.